|
Post by jeff73 on May 5, 2021 14:23:49 GMT -6
I have 82 cutlass weighs 2950 me in it 900#lf 1050rf 200lr 150rr lf weighs812 rf741 lr790 rr603 cross51.9o% left54.81 rear47.20 bite195,anyway to get weight off front? Have lightened as much I can (aframes,motor set backetc) is there different spring rates that would make this better? No weight rule but cannot ad weight no ballasts any help would be greatly appreciated fuel tank in trunk left side along with battery
|
|
one8
Fourth Place
Posts: 52
|
Post by one8 on May 10, 2021 16:08:02 GMT -6
What are your ride heights and spring lengths? I assume you're running a nose piece with a tube bumper and not the heavy stock one. Get the seat and controls as far back as you're allowed. You might look at hiding blast in the rear frame horns. I've seen guys use round bar stock instead of tubing for rear down tube braces. Secret ballast!
|
|
|
Post by jeff73 on Jun 23, 2021 1:14:19 GMT -6
I'm back,was hospitalized for a bit,but changes to the car is,lf spring800# using 4 offset weight is 750#rf900#3offset weight 771#lr300#4offsetweight973#rr175#3offsetweight681# 12inch springs in front 14inch in rear ride heightlf9.75 rf8 lr10.50 rr9 left%54.26 rear%52.07 cross%54.94 bite 293 weighed full gas me in it I weigh 210# 22gal mounted in trunk on ds batt.mounted in middle of trunk, car is tight in mid corner and no traction exiting on dry slick track 3/8 mile slight banking
|
|
one8
Fourth Place
Posts: 52
|
Post by one8 on Jun 23, 2021 13:31:45 GMT -6
That's a $#it ton of bite! I'd put the #200 spring back in the LR. Probably turns in great with the left rear dragging.
|
|
|
Post by jeff73 on Jun 23, 2021 16:19:30 GMT -6
Ok will do, what is a good # for bite? It also seems like left rear picks up in the corner, thank you for your help and knowledge,I appreciate it!
|
|
one8
Fourth Place
Posts: 52
|
Post by one8 on Jun 24, 2021 9:21:50 GMT -6
I try not to go over #130. But it depends on the track condition and driving style. More bite will help the car rotate on entry but cause the issue you're having with a push center-off. I'm running 105# of bite right now with a 1" spacer in the LR. If I pull the spacer I get 125# of bite.
|
|
|
Post by jeff73 on Jun 24, 2021 12:17:50 GMT -6
Thats great info.,I put 200 spring in lr # are left 54.31 rear51.94 cross51.46 bite182 4 offset ds 3 onps, weights are lf806#rf716#lr914#rr732#,try it this way? Or is there anything else that seems out of wack,besides the driver,lol, thanks again for your help
|
|
|
Post by jeff73 on Jun 24, 2021 12:21:04 GMT -6
I forgot to mention can't run spacers and only 3 and 4 offset
|
|
one8
Fourth Place
Posts: 52
|
Post by one8 on Jun 25, 2021 14:18:12 GMT -6
Those are pretty restrictive wheel and spacer rules. Have you checked the stagger on your tires? Maybe run very little stagger in the front and as much as you can get in the rear. You should be able to fine tune it with air pressure after that. Otherwise I would run 4" offset wheels on all but the RR. Run a 3" there. What tires do you run? We run asphalt pull offs and I don't go more that 16# of air pressure in the RF.
|
|
|
Post by jeff73 on Jun 25, 2021 18:33:16 GMT -6
205 70 15 dot street tires tires have to be same size all the way around
|
|
one8
Fourth Place
Posts: 52
|
Post by one8 on Jun 26, 2021 9:18:56 GMT -6
Ok. So youre running quite a bit of air pressure then. I'd still air them all up to the highest pressure you run and check the rollout on them. You probably won't get much stagger though. Other than that you could add a little weight to the right rear of the car or swap your front springs and go with reverse split. That'll take a little bite out of the car also. Quite a few guys run like that. Especially if your track is smooth and slicks off by the feature.
|
|
|
Post by jeff73 on Jun 28, 2021 16:10:07 GMT -6
Ran the car but only in the heat,got rained out, but started in the back and finished 2nd, was a lot better but didn't want to turn mid corner,I think because it was so slimy,gonna swap springs around in front and give another try,but your help has made it 100% better couldn't thank you enough! Let you know how it goes!😃
|
|
one8
Fourth Place
Posts: 52
|
Post by one8 on Jun 28, 2021 16:36:54 GMT -6
Right on! Glad to hear it and glad I could help. My car was good Saturday night. Got dumped in the heat race though. Passed 4 cars to get the last transfer out of the B. Then it got real hot after 4 laps in the A.
|
|
one8
Fourth Place
Posts: 52
|
Post by one8 on Jun 28, 2021 16:49:54 GMT -6
Also. If your track gets as slick as the one I run by the feature. You may want to hold off on the changes. As the track slicks off you need a tighter car to turn. Otherwise you'll have a hard time keeping the rear from coming around. It took me a while, and some stearn coaching,to figure out that I wasn't driving the car in hard enough to get the weight to transfer to the right. Car always seemed push like a dump truck mid corner. Now I drive it in as far as I can until it feels like the rears going to come around. So much more fun! 😁
|
|
|
Post by jeff73 on Jun 28, 2021 17:58:49 GMT -6
Thanks!I will keep that in mind,thanks again for all your great knowledge!🏁
|
|